Press "Enter" to skip to content
Rebuilding/Revalving Smooth Body Shocks (King version)

Rebuilding/Revalving Smooth Body Shocks (King version)

Filed under Suspension. See all how-to guides.

I've discussed the trade-offs between disposable and rebuildable shocks in the past as I've replaced spherical bearings in my ADS coilovers, but I've never walked through the process of actually rebuilding the internals of a smooth body shock before. But, now that my shocks have absorbed some ~50K miles, it's time to rebuild and revalve them - so they can provide the same great service in the years to come, as they carry me and my stuff over thousands of miles of dirt roads.

Related Guides

Every shock manufacturer makes their shocks a little differently. I originally learned how to do this work by watching the rebuild of a King shock, and applied it to my own ADS. However, I recognize that it's always nice to have a guide that matches your exact setup, so I've created guides for each manufacturer that I've encountered.

Rebuilding/Revalving Smooth Body Shocks (ADS version) Rebuilding/Revalving Smooth Body Shocks (ADS version)
Rebuilding/Revalving Smooth Body Shocks (King version) Rebuilding/Revalving Smooth Body Shocks (King version)

Parts and Supplies

In order to rebuild your shocks, you'll need several replacement parts and supplies. I'm sure there are numerous places to get these, but I recommend Ben at Shock Services, LLC. And - if it seems too intimidating to tackle this yourself, you can even send him your shocks and he'll do the rebuild (and/or revalve) for you.

For each shock you are going to rebuild, you will need the following:

  • To replace the bearings (all of these parts are available in a kit)
    • Two (2) spherical bearings. I recommend going with FK brand bearings in -F1 tightness (extra tight), and either the FKS10T-F1 (hardened steel) or FKSSX10T-F1 (stainless steel) versions.
    • Four (4) C-clips
    • Misalignment spacers
  • To replace the seals - purchase a kit for your shock brand. Note that if you have clickers or bypasses, or no resis, you may need different seal kits. Contact Tim, or your manufacturer.
  • If you are revalving your shocks at the same time, you'll need the appropriate shim stack. Contact Ben to determine (for a fee) the right set of shims for your needs.
  • Shock Oil - you'll need approximately 1 gallon for two (2) shocks w/resis.

Parts for four shocks.

Tools

One of the reasons to pay someone like Tim to do this work for you is that many of the tools to do the job are specialty tools, and unlike other tools that can be used on other jobs, these are primarily used for rebuilding shocks, so it will take a while to amortize the cost.

Some of the specialty tools needed for the job.

Terminology

Thanks to King Shocks for making this nifty diagram that labels all the parts of the types of shocks that this guide/tutorial covers rebuilding. The guide doesn't touch on all these parts, but if it references a part you are unfamiliar with, you can likely find it here.

Anatomy of a shock.

1 - Top Cap
2 - Top Cap O-Ring
3 - Secondary Nuts
4 - Secondary Nut O-Ring
5 - Shock Cylinder
6 - Coil Adjustment Nut
7 - Coil Spring
8 - Coil Slider
9 - Coil Plate
10 - Piston Retaining Nut
11 - Piston Retaining Washer
12 - Valve Shims
13 - Piston Wear band
14 - Piston
15 - Base Washer
16 - Top Out Washer
17 - Shaft Spacer
18 - Shaft Guide / DU Bushing
19 - Seal Cap
20 - Shaft O-Ring
21 - Main Seal
22 - Main Seal Retainer
23 - Seal Cap O-Ring
24 - Shock Cylinder C-Clip
25 - Wiper Cap O-Ring 26 - Wiper Cap
27 - Wiper Seal
28 - Set Screw
29 - Shock Shaft
30 - Rod End
31 - Coil Adjustment Pinch Bolt
32 - Piggyback Mounting Sleeve
33 - Reservoir C-Clip
34 - Piggyback Adaptor O-Ring
35 - Piggyback Reservoir Oil End Cap
36 - Reservoir O-Rings
37 - Reservoir Cylinder
38 - Reservoir Piston Wear Band
39 - Reservoir Piston
40 - Remote Reservoir Air End Cap
41 - Schrader Valve
42 - Piggyback Mounting Plate Bolts
43 - Piggyback Mounting Plate
44 - Piggyback Reservoir End Cap Bolts
45 - Spacer
46 - Bearing C-Clips
47 - Spherical bearing
48 - Piggyback Mounting Sleeve O-Rings
49 - Piston O-Ring
50 - Main Seal C-Clip 51 - Wiper Seal C-Clip
52 - Wiper Seal Retainer
53 - Wiper Seal
54 - Wiper O-Ring
55 - Wiper Cap Bolts
56 - Remote Reservoir Hose
57 - Remote Reservoir Oil End Cap
58 - Remote Reservoir End Cap O-Ring
59 - Schrader Valve Cap O-Ring
60 - Schrader Valve Cap
61 - Piston Bleed Screw
62 - Seal Cap Bleed Screw
63 - Bypass Valve
64 - Bypass Spring
65 - Bypass Valve Stop
66 - Bypass Valve Stop Set Screw
67 - Bypass Valve Stop O-Ring
68 - Bypass Adjusting Nut O-Ring
69 - Bypass Adjusting Nut
70 - Bypass Adjusting Screw
71 - Bypass Adjusting Jam Nut

There's a Video

The good folks - well, Ben, actually - over at Filthy Motorsports put together a video of an entire King smooth body shock rebuild. I watched that video in order gain the confidence to rebuild my ADS shocks, and while things are constructed a bit differently, it was a fantastic resource. Ben was also gracious enough to let me include photos of his work here in this King walkthrough, so that those who prefer a step-by-step guide have the same benefit as ADS. Thanks Ben!

Doing the Job

There are really three parts to a shock rebuild - removal/installation of the shocks, work on the external components (bearings, etc.), and work on the internals (seals, shims). I'll only cover work on the external and internal components here; since removal/installation of the shocks is shock-specific and - I assume - general knowledge. As such, this guide starts when the shock(s) you plan to rebuild are sitting on the bench.

Additionally, this process is the same for shocks most shocks with reservoirs, whether they be, though each may have more/fewer seals to replace:

  • remote or piggyback reservoirs
  • have (or not) clickers
  • have (or not) bypasses

Lastly, some steps are specific to coilover (generally front) shocks, and can be skipped for non-coilover applications.

Removing the Coil Spring (coilovers only, obviously)

Compressing coils to remove them from coilovers can be a dangerously touchy operation. A wall-mounted spring compressor is clearly the safest tool for this job, but doesn't come cheap. Another option - that is safer than using one of the spring compressors you can rent at a parts store - is to take your coilovers to a shop and pay them a few bucks to remove/install the coils on their wall-mounted unit. Shouldn't be too expensive, really.

  1. Place the coilover in the spring compressor with the bottom of the shock pointed up, and the end with the reservoir hose pointed down.
  2. Record the number of threads showing between the coil adjuster nut (preload collar) and the top of the shock, so that you can reinstall it in the same position later.
    Number of threads showing: __________.

    Orienting the shock in this fashion will allow it to be removed from the spring, while the spring is still compressed.

  3. Use the appropriately sized Allen wrench to loosen the bolt that locks the coil adjuster nut (preload collar) in place.
  4. Use the spring compressor to compress the spring until the spring is not exerting any pressure on the lower coil plate or coil adjuster nut.
  5. Rotate the coil adjuster nut to move it to the top of the shock housing.
  6. Remove the lower coil plate by finding the gap, sliding it down off of the rod end, and then sliding it off the shock shaft. Note: at this point, the entire shock shaft and housing will want to fall down through the spring and onto the floor. Instead, lower it gently.

    This gap in the lower coil plate allows it to slide over the shaft once it is disengaged from the rod end.

Removing the Spherical Bearings

  1. Clean out as much grease/grime from the rod end as possible.
  2. Use a pair of internal snap ring pliers to compress, and then remove, the snap rings from each side of the spherical bearing. Note: technically you only need to remove one snap ring, but the process of pressing out the spherical bearing is easier if you remove them both.

  3. Using a shop press and two sockets - one large enough to capture the spherical bearing as it is pressed out, and one that presses on the outer race of the spherical bearing to push it out - carefully press the spherical bearing out of the rod end.

  4. Inspect the rod end for excessive wear, and use a bit of sandpaper to clean up the surface if necessary. Note: the rod end is often aluminum and so quite soft compared to the steel bearings. If excessive wear is present, or if the bearing does not fit snugly, replace the rod end.

Installing New Spherical Bearings

It is recommended - though not strictly necessary - to use new snap rings when you install new spherical bearings.

  1. Use a pick to clean out the snap ring grooves in the rod end.
  2. Use the internal snap ring pliers to compress, and then insert, a new snap ring into one of the snap ring grooves. Note: The new spherical bearing will be pressed in until it bottoms out on this snap ring.
  3. Spread a bit of grease on the outside of the spherical bearing and on the inside of the race in the rod end.
  4. Using a shop press and two sockets - one large enough to support the rod end, and the other that presses on the outer race of the spherical bearing, slowly press the new spherical bearing into the rod end until it bottoms out on the snap ring.Note 1: It is extremely important that the bearing go in square, and smoothly. If it does not go in square, it will damage the aluminum rod end race, and you'll need to buy a new rod end.Note 2: Once the bearing bottoms out on the snap ring, stop. Do not over press.

    Once the bearing is seated, you will be able to see the groove for the second snap ring.

  5. Use the internal snap ring pliers to compress, and then insert, a new snap ring into second of the snap ring grooves, capturing the spherical bearing.

Depressurizing and Removing the End Cap from the Reservoir

  1. Remove (unscrew) the cap on the Schrader valve at the end of the reservoir.
  2. Point the reservoir away from you, and use a valve core tool to release the pressure from the reservoir. Note: if there is no pressure released, then the shock has lost pressure. The most common cause of this is a valve core that has rattled loose.
  3. Use the valve core tool to remove the valve core. This valve core can be reused if it is in good shape.

    With the valve core removed, the gas chamber of the reservoir can now breath freely.

  4.  Use your thumbs to evenly push the end cap approximately an inch into the body of the reservoir in order to expose the retaining ring.

  5. Use a pick to remove the retaining ring. This retaining ring can be reused if it is in good shape.

  6. Clean any residual dirt out of the reservoir with a paper towel.
  7. Thread the valve core tool onto the end of the Schrader valve and use it to carefully pull the end cap out of the reservoir.

  8. Inspect the inside walls of the reservoir for scaring/marks/oil. A small amount of oil is normal, a larger amount may indicate a problem. If the inside walls are in reasonable condition, clean out any oil with a paper towel.
  9. Inspect the end cap for scaring/marks. If it is in reasonable condition, set it aside, otherwise consider purchasing a new end cap.

Measure the Distance to the Internal Floating Piston in the Reservoir

These steps are necessary in order to establish the amount of oil that will be added to the shock during the rebuild process.

  1. If your reservoirs have clickers, turn them until they are fully opened up, so oil can flow freely.
  2. Fully extend the main piston on the shock.
  3. Use a tape measure to measure the distance from the outer edge of the reservoir to the deepest point (center) of the piston.
  4. Record the position for later use: _____________ Note: there should really only be 1.5-2.5 inches of oil in the reservoir, certainly less than 50% of the reservoir length.

Removing the Wiper Cap from the Shock

  1. Locate the set screw(s) on the bottom of the wiper cap, and clean out any grit/dirt/grime so that the appropriately sized Allen wrench can be inserted into the set screw. Note: if you break or strip this set screw, you have to drill it out, which is difficult with the shock shaft in the way.

    The set screw locks the wiper cap against the internal shaft retainer, and only needs to be loosened enough to allow the two components to spin independently.

  2. Carefully break the set screw loose, and then loosen - but do not remove - it.
  3. Use the Shock / Reservoir Housing Wrench (manufacturer specific) to loosen the wiper cap, then unscrew it completely and slide it down the shock shaft.

    There should be no oil inboard of the wiper cap.

Removing the Internal Shaft Retainer and Shock Shaft

This part of the procedure results in removal of the entire shock shaft from the housing, which means that the oil in the shock is also released. Be prepared, and have a catch container on hand to capture the used oil.

Note: removing the internal shaft retainer is similar to removing the end cap from the reservoir.

  1. Position the shock vertically so that the shaft of the shock is pointed up and the shock housing is seated on the work bench. This allows you to press down on the internal shaft retainer.
  2. Place the two halves of the 1" PVC pipe around the shock shaft, on the internal shaft retainer.
  3. Slide the wiper cap down on the PVC pipe, and press down on the wiper cap to press the internal shaft retainer into the shock housing. Note: this will take some pressure.

  4. Use a pick to remove the retaining ring. This retaining ring can be reused if it is in good shape.
  5. Place the shock in a bucket or over a catch container to capture oil that will come out in the following steps.
  6. Slowly pull/work the shaft out of the shock body.

  7. Allow the shock to drain for 5-10 minutes, or clean the shock shaft and shock body with paper towels to remove residual oil.

Note 1: if it is too difficult to pull the shock shaft out of the body at this point, replace the end cap, retaining ring and Schrader valve on the reservoir, and use a small bike pump to add no more than 2- to 3-psi to the reservoir.

Note 2: With minimal pressure in the reservoir, you can also slowly push the shock shaft into the housing, which will displace some oil, and force the internal shaft retainer out the end of the shock housing.

Removing the Internal Floating Piston from the Reservoir

Ensure that most of the oil is drained from the shock housing before proceeding. More oil will come out during this procedure, so be ready to capture it as well.

  1. If the reservoir end cap and retainer ring were reinstalled to pressurize the shock in order to remove the shock shaft, remove them again (procedure above).
  2. Locate the internal floating piston in the reservoir and note the small threaded hole in the center.
  3. Thread a Reservoir Piston Positioning Tool into the internal floating piston. Note: a 1/4"x20 threaded rod can also usually be used for this operation.

  4. Pull the internal floating piston out of the reservoir. Note: you may need to overcome a vacuum at the beginning, but then the piston should slide relatively easily.

  5. Drain any oil from the reservoir, hose, and shock tube into your catch can.
  6. Clean out any residual oil from the reservoir and shock tube with paper towels.

Replacing the Seals on the Internal Floating Piston from the Reservoir

  1. Use a pick to remove the large o-ring on the outside of the internal floating piston. Note: this o-ring presses on the wear ring, which should be removed if it is not already. The wear ring will be reused.
  2. Clean up the internal floating piston, to remove all dirt and oil that might be present.
  3. Find the new seals/o-rings from the seal kit that match the existing seals you removed.
  4. Place a small amount of shock oil in a bowl so that you can dip each new seal/o-ring prior to installation.
  5. Install the large o-ring onto the outside of the internal floating piston. Note: do not install the wear ring at this time.

Disassembling the Shock Shaft Assembly

The order of components on the shock shaft assembly is critical. As such, it is recommended to perform these steps to one shaft assembly at a time, keeping the other for reference. And of course, be sure to keep things in order as you remove them.

  1. Place the lower shock eye of the shock shaft assembly in a vice with non-maring jaws.
  2. Photograph the shock shaft assembly for future reference.

  3. Remove the shaft nut. Note: this should take a bit of force, but nothing unreasonable.
  4. Remove the shaft nut spacer.
  5. Remove the rebound shims, maintaining their order. Note that on OEM kits, these may be in a small holder.
  6. Remove the wear band surrounding the piston if it hasn't already separated itself from the piston.
  7. Remove the piston. Note: be careful at this point - the compression shims often stick to the bottom of the piston.
  8. Remove the compression shims, maintaining their order.
  9. Remove the washer that supports the compression shims.
  10. Remove the internal shaft retainer. Note: sometimes the main seal retainer sticks to the shaft at this point. Be sure to pull it off the shaft and place it back into position at the bottom of the internal shaft retainer.
  11. Remove the wiper cap.

Replacing Seals on the Internal Shaft Retainer

  1. Remove the main seal retainer and then use a flat screwdriver to remove the main seal. Note: the main seal has a groove on one side of it, and the orientation must be maintained on reinstallation.

  2. Use a pick to remove an o-ring that is located under the main seal.
  3. Use a pick to remove the large o-ring on the outside of the internal shaft retainer.
  4. Clean up the internal shaft retainer, to remove all dirt and oil that might be present.
  5. Find the new seals/o-rings from the seal kit that match the existing seals you removed.
  6. Place a small amount of shock oil in a bowl so that you can dip each new seal/o-ring prior to installation.
  7. Install the large o-ring onto the outside of the internal shaft retainer.

  8. Install the smaller internal o-ring into the shaft retainer.
  9. Install the main seal - groove down - into the shaft retainer. Note: this can be difficult, take your time to seat the seal correctly.

  10. Place the main seal retainer onto the main seal.

Replacing Seals on the Wiper Cap

  1. Wearing heavy gloves, place the outside surface of the wiper cap in the palm of your hand.
  2. Place an appropriately sized socket on the inside surface of the wiper seal, ensuring that it does not contact the metal of the wiper cap.
  3. Use a rubber mallet to knock the wiper seal into the palm of your hand. Note: a more traditional press setup can be used for this procedure as well.

  4. Use a pick to remove the large o-ring on the outside of the wiper cap.
  5. Clean up the wiper cap, to remove all dirt and oil that might be present.
  6. Find the new seals/o-rings from the seal kit that match the existing seals you removed.
  7. Place a small amount of shock oil in a bowl so that you can dip each new seal/o-ring prior to installation.
  8. Ensure that the set screw is not protruding past the outer surface of the wiper cap.
  9. Place the wiper seal in place on the outside surface of the wiper cap, and place the assembly in the press, with a plate above and below the wiper cap and seal.
  10. Slowly press the wiper seal into the wiper cap until it is flush with the outside surface, ensuring that it goes in smoothly and square.

  11. Install the large o-ring onto the outside of the wiper cap.

Replacing the Seals on the Shock Piston

  1. Use a pick to remove the large o-ring on the outside of the piston. Note: this o-ring presses on the wear ring, which should be removed if it is not already.
  2. Clean up the piston, to remove all dirt and oil that might be present.
  3. Find the new seals/o-rings from the seal kit that match the existing seals you removed.
  4. Place a small amount of shock oil in a bowl so that you can dip each new seal/o-ring prior to installation.
  5. Install the large o-ring onto the outside of the piston. Note: do not install the wear ring at this time.

Inspecting and Cleaning the Shaft

  1. Inspect the shock shaft for straightness.
  2. Inspect the shock shaft for any chips or imperfections. If any are found, use an emory stone and some shock oil to lightly sand/polish the area to remove the imperfections. Note: do not use Emory cloth or sandpaper for this operation.

Assembling the Shock Shaft Assembly

  1. Spread a little shock oil on the shaft to assist with lubrication of the seals as they slide over the shaft.
  2. Unthread the set screw on the wiper cap (which was re-inserted when the wiper seal was pressed in), and slide the wiper cap onto the shaft.
  3. Slide the internal shaft retainer onto the shaft.
  4. Thread the internal shaft retainer and wiper cap together a little bit - not fully - just to keep them square on the shaft.
  5. Slide the washer that supports the compression shims onto the shaft.
  6. Slide the compression shim stack onto the shaft.
    • Note: the shims should generally form an inverted pyramid at this point, with the smaller shims toward the washer and the larger shims toward the piston.
    • Note 2: if you are revalving your shocks at the same time as a rebuild, now is the time to ensure the correct order of your new compression shim stack.
  7. Slide the piston onto the shaft. Note: the side with more large holes should face up toward the rebound shims; the side with fewer large holes faces down toward the compression shims.
  8. Slide the rebound shim stack onto the shaft.
    • Note: the shims should generally form a pyramid at this point, with the larger shims toward the piston.
    • Note 2: if you are revalving your shocks at the same time as a rebuild, now is the time to ensure the correct order of your new rebound shim stack.
  9. Slide the shaft nut spacer onto the shaft.
  10. Reinstall the shaft nut. Note: if this is a locking nut in good shape, you can reuse it. If it is a non-locking nut, a small amount of blue loctite can be used.

Inserting the Internal Floating Piston into the Reservoir

  1. Spread a bit of shock oil onto the o-ring of the internal floating piston.
  2. Support the reservoir on a vertical position, with the opening facing up. Note: this may be difficult with the reservoir hose, but some strategic placement of supports will work.

  3. Position the internal floating piston in the reservoir, with the smooth side down, and press it into the reservoir just far enough for the o-ring to clear the groove for the retainer ring.
  4. Position the wear band around the internal floating piston and use your fingers keep the wear band pressed against the piston as you carefully, and squarely, press the piston and wear band into the reservoir.

  5. Carefully push the internal floating piston all the way into the reservoir housing, until it bottoms out.
  6. Temporarily install the retaining ring in the end of the reservoir. Note: this is to keep the internal floating piston from pushing out of the reservoir as oil is added to the shock.

Filling the Reservoir with Oil

  1. Secure the shock in a vise with the opening facing up and the reservoir - and reservoir tube - hanging down. Note: this orientation is important so that as oil is added to the shock, it will flow down into the reservoir, allowing air bubbles to rise up through the oil and out of the shock.
  2. Thread the Reservoir Piston Positioning Tool into the internal floating piston of the reservoir. Note: This will be used to cycle shock oil into the reservoir, and push air from the reservoir back out through the shock.

  3. If your reservoir has compression adjusters, be sure that they are fully open.
  4. Fill the shock approximately halfway with oil.

  5. Use the Reservoir Piston Positioning Tool to pull the internal floating piston toward the end of the reservoir, drawing oil into the reservoir.
  6. Use the Reservoir Piston Positioning Tool to push the internal floating piston away from the end of the reservoir, pushing air and oil out of the reservoir.
  7. Repeat steps 5 and 6 until no more air is being expelled from the reservoir.
  8. Use the Reservoir Piston Positioning Tool to pull the internal floating piston away from the end of the reservoir, until the distance from the end of the reservoir tube to the deepest part of the piston is 3/8" less than the measurement taken when disassembling the reservoir. Note: this is not the final positioning, which will be done later.

Inserting the Shock Shaft and Filling the Shock with Oil

This part of the operation can be a bit tricky. The idea is to get as much oil into the shock housing as possible, and to have no air bubbles.

  1. Move the end cap and internal shaft retainer as far down the shaft as possible (toward the rod end, away from the piston).
  2. Reinstall the wear ring onto the piston.

  3. Carefully seat the piston and wear band into the shock housing, just past the groove for the retaining ring.
  4. Press the shock shaft into the housing just until the piston reaches the oil level, and then continue pushing until it is just below the oil level. Note: some oil may jump up as it presses through the piston, so you may want to cover the shock tube opening with a towel.
  5. Cycle the piston up and down below the oil level several times to remove any trapped air/bubbles.
  6. Fill the shock housing with shock oil, to within 1.5 inches of being full.
  7. Pull the shock shaft up until the piston is at the oil level, but does not break the surface of the oil.
  8. Fill the shock housing with shock oil, to the level of the groove for the retaining ring.
  9. Slide the internal shaft retainer down toward the shock tube, just until the o-ring contacts the end of the tube.

  10. Holding the internal shaft retainer in place with one hand, slowly and carefully push the shock shaft down into the shock housing - displacing oil and any trapped air - until you see just a little bit of oil pressing up around the o-ring. Note: at this point, you've pushed all the air out of the shock.
  11. Use both hands to push the internal shaft retainer into the shock housing, just far enough to expose the retaining ring groove.
  12. Insert the retaining ring into the retaining ring groove.
  13. Pull the shock shaft out of the shock as far as possible, which will begin to pull the internal shaft retainer up toward the retaining ring.
  14. Use the Reservoir Piston Positioning Tool to push the internal floating piston further into the reservoir, pushing oil out of the reservoir and into the shock tubing. This will push the internal shaft retainer toward the retaining ring until it is seated.

  15. Measure the distance from the end of the reservoir tube to the deepest part of the piston. This should be approximately the same as your original measurement, with 1.5-2.5" of oil in the reservoir. Note: if the oil level is not correct, correct it before proceeding.
  16. Slide the wiper cap down the shock shaft and thread it onto the internal shaft retainer until it is snug, but do not fully tighten it yet - as the shock is not pressurized, it will continue to spin.

Replacing the End Cap on the Reservoir

  1. Use a pick to remove the retaining ring that was installed to keep the internal floating piston from pushing out of the reservoir in previous steps.
  2. Spread some shock oil onto the o-ring of the end cap, and use your fingers to press the end cap into the reservoir, past the retaining ring groove.
  3. Insert the retaining ring into the retaining ring groove.
  4. Thread the valve core tool into the valve core on the end cap and pull the end cap back toward the end of the reservoir, until it is seated on the retaining ring.

  5. Reinstall the valve core in the Schrader valve housing.

Pressurizing the Shock and Securing the Wiper Cap

  1. Mentally go through a checklist to ensure that:
    1. You have retaining rings everywhere they are supposed to be.
    2. You don't have any spare parts that should have been installed.
    3. Fittings for hoses, etc. are tight.
  2. Set the regulator on your nitrogen tank to 100psi.
  3. Charge the reservoir with nitrogen. Note: you may notice the reservoir end cap and/or shock wiper cap move slightly at this point as they are fully seated against the retaining rings.

  4. Secure the wiper cap by screwing it onto the internal shaft retainer. Note: you want it to be tight, but not too tight
  5. Secure the wiper cap set screw. Again, tight, but not overly so.

Pressure Testing and Final Pressurization

This process over pressurizes the shocks for a short period of time to ensure that there are no leaks before the final pressure is set and the shocks are put back into service.

  1. Set the regulator on your nitrogen tank to 350psi.
  2. Charge the shock with nitrogen.
  3. Allow the shock to sit on the bench for 24-48 hours, to ensure that no oil leaks out. Note: If oil does leak out, disassemble the shock and correct the issue.
  4. After the shocks have set for an extended period, if no oil has leaked out, check the pressure of the nitrogen in the reservoir. Note: this is a small volume of gas, so simply checking it will result in a significant drop in pressure. The reading should be similar to, but certainly lower than, the 350psi that was charged. Something in the 325psi range is reasonable.

  5. If there are no leaks, reduce the pressure to 200psi

Your shocks are rebuilt and ready for another 50K miles of service.

 

 

 

 

 

 

 

 

 

2 Comments

  1. Tom Schneider
    Tom Schneider February 28, 2023

    Perfect pictures and videos from your web site. I would not have been able to rebuild my shocks without the information you provided. I made that rod for pulling the floating piston like you mentioned. The "Reservoir Piston Positioning Tool". I actually made a small upgrade to it. In the center of the rod, I added a nut, a washer then another nut and adjusted it to the bottom of the cylinder when it was screwed in. I used it to make sure I had the same distance and measurement set for the floating piston after bleeding the air out and the shock was reassembled.

    Reply
    • turbodb
      turbodb February 28, 2023

      That's a great addition Tom! Glad the write-up helped you, and you were able to tackle it yourself. ?

      Reply
Leave a Reply

Your email address will not be published. Required fields are marked *