July 23, 2017. Ham radio is for old guys. I must be getting old. As the truck has gotten more capable, and as we’ve started doing longer and more remote trips, I’ve started carrying more tools, extra parts, etc. in order to make (minor) road repairs - hopefully enough to limp back to civilization. But in the back of my mind there is always a little voice that’s been saying, “What happens if you’re many miles out?” I knew I needed some sort of ability to communicate. I considered getting an inReach device a SPOT tracker, or some other ePRB/PLB,…
2 CommentsYear: 2017
July 22, 2017. It was July 8, 2017. I know because I will always remember the day @mrs.turbodb said, "You should just get a fridge for the truck." We'd just returned from our week-long trip to Canada with the little kiddo, where we'd pre-prepared and frozen many of our meals, using our crappy 48qt cooler to keep everything chilly. Of course, even sandwiched in the middle of our gear and under the CVT, we had to get ice every day (does Canada not have block ice?) - which meant staying relatively near civilization. So when we started talking about our…
3 Comments
July 15, 2017. The truck has always had a bit of rake, with the rear being ~2-3” higher than the front. And I like it that way - it looks good. Until the constant weight of the bed rack and CVT, the combination of stock leafs, Deaver AALs, and air shocks that I installed as part of the suspension overhaul were working reasonably OK. “OK” because I’ve never been able to get the air shocks to hold pressure - they lose about 10lbs a day, so I’m constantly filling them (which is easier with the ARB compressor installed). But with…
4 Comments
June 30 - July 7, 2017. June 29, 11pm: we finally decided to head to Canada for a week of camping. We’d leave the next morning at 7am sharp. It was going to be awesome! But let’s rewind… We’ve been wanting to go to some of Canada’s National Parks for a while. So, in late 2016 when we discovered that Canada was celebrating their 150th anniversary by giving away free access to their national parks for 2017, we jumped on the opportunity to get a pass, and we started working out plans to hit Banff and Jasper during the summer.…
Leave a Comment
June 18, 2017. As our excursions have been getting longer and more remote, I’ve started paying more attention to things like the amount of extra fuel and water we carry. It’s still nothing too extreme - 6 gallons of fuel (50-100 miles) and 6 gallons of water (several days). And for convenience of packing, I’ve switched over to Rotopax from the cheapo red plastic gas cans and 1-gallon milk jugs. Of course, even finding deals on Craigslist means that I’ve spent a small fortune on the containers. But, they look great and are relatively compact when a trip gets started……
Leave a Comment
May 25, 2017. I’m not getting any younger, that’s for sure. It used to be that I could do all kinds of manual labor for 20 hours/day, wake up the next day, and do it all again. I’d hurt myself in some semi-major way and my body would heal itself quickly. Now, I get a little cut somewhere and it takes a week to heal. And if I work for 20 hours one day, I want to sleep for 20 hours the next. With all that in mind, I quickly realized that I needed a better way to fill my…
Leave a Comment
Oregon-bound Chapter 3: Mission Impossible: Oregon's Backcountry Discovery Route May 11-15, 2017. Day 1: Thursday, May 11. Parting ways with Pops and my Uncle, our plan was to run the OBDR from Seneca, OR to Walla Walla, WA, and then the WABDR from the border up to Cle Elum - approximately 1000 miles of remote back roads in four days. We knew it'd be a lot of driving, but we've driven a lot for other trips. We were sure we could do it - it's not like we'd be going 10 mph the whole time. At least we were right…
Leave a Comment
May 8-10, 2017. Day 1: Monday, May 8. Acquisition and installation of the CVT successful, we were off for a week of desert and back country exploration - so awesome. The first few days would be exploring the Malheur National Wildlife Refuge area with Dad and uncle, followed by four days on the Oregon and Washington Backcountry Discovery Route (OBDR and WABDR) to get from central Oregon back to I-90 around Cle Elum and then ultimately back to the Seattle area. A couple hours driving from Bend to Hines/Burns and we met up with the rest of the gang. My…
Leave a Comment
May 8, 2017. The day is here, and it's a big one. It was over half a year ago that I decided I wanted a CVT, and in that time I'd purchased one and fabricated a bed rack that I hoped would work to hold it behind the cab of the truck. Naturally I'd gotten a good deal on the CVT, and had spent 10x more fabricating the rack (buying tools, etc.) than if I'd just purchased a pre-fabricated one. This day was also a big day because it was the start of a week-long camping trip where we'd meet…
2 Comments
April 2, 2017. Thousands of miles. How far have I travelled on washboard roads at full tire pressure? Definitely thousands of miles. Probably not ten thousand, but enough that I wish I’d have known how much better life is when you can air down and air back up without too much hassle. Luckily, while I’m still cheap, I’ve smartened up over the years, and I know that some things are worth a little extra. And comfort is one of those things. So, it’s time to install an ARB CKMA12 air compressor. I’ve opted for the single compressor here rather than…
Leave a Comment
April 2017. Wires everywhere. That’s how it’s starting to feel with the various accessories that I’ve added to the truck. Sure, I tuck them away here, and zip-tie them away there to try to clean things up, but in the end I still have several pair of wires running from various fuses and relays in the engine compartment to accessories and switches on the truck. As someone who likes organization, it’s always bothered me. Luckily, there are solutions out there for those of us who like order. There are pre-made fuse boxes from folks like Blue Sea Systems, and there…
Leave a Comment
February 14, 2017. You may recall that no too long ago I decided to purchase a CVT, and then of course realized that the truck would need a bed rack to attach said CVT. That led to my Millermatic 211 acquisition, and the realization that this bed rack was the beginning of yet another expensive hobby (metalwork). Excited to get going, I started looking for bed rack designs. I wanted something that would support the CVT - both on the road as well as deployed would position the top of the CVT "in-line" with the top of the cab -…
Leave a Comment