Let's see, how did this start last time. Ahh, right... For two years now, my A/C hasn't really worked. At some point - 17 years after it was originally installed - it developed a slow leak. As spring turned to summer in 2018, I noticed that - as Nelly might say - "it's getting hot in herre," even as I cranked up the cold.from It's Too Damn Hot In Here - Fixing the A/C Evap Core Well, I replaced the A/C evap core and things worked well for all of one week. While that sounds bad - and I guess…
2 CommentsCategory: Tacoma Maintenance
General catch-all category for content relating to 2000 Tacoma maintenance.
For two years now, my A/C hasn't really worked. At some point - 17 years after it was originally installed - it developed a slow leak. As spring turned to summer in 2018, I noticed that - as Nelly might say - "it's getting hot in herre," even as I cranked up the cold. For a while, I ignored it. There was no way I was ready to tackle the A/C system from a skills perspective - or so I thought at the time - and I knew that taking it to a shop was going to be rather expensive.…
Leave a Comment
It seems like just a few weeks ago that I replaced the spherical bearings on my ADS coilovers for the first time, though it turns out, it was actually a few (4) months ago. Prior to that, I'd put some 27K miles on the new ADS suspension (see installation) - miles that really proved to me that it was a worthwhile investment. Unfortunately, on our last trip down to the Eastern Mojave, the coilovers had been squeaking again. Well, really they'd been squeaking before we even left - but with only 7K miles on the odometer since the previous change,…
Leave a Comment
On our last trip to the Eastern Mojave, one of the things I noted early in the trip - actually, before the trip even started really - was that the battery in the cab seemed low. I chalked it up to an error on my side and figured that the long 20-hour drive from home to our first hike would be enough to get it back up and kicking. It sort of did, but the battery seemed weak the entire trip, dropping below 12V reasonably quickly - much more quickly than it has in the past. Initially I figured that…
3 Comments
Over the last couple years, I've learned - mostly from others experience - that it's a good idea to keep an eye on 1st gen Tacoma lower ball joints (LBJs). If you do lots of bumpy, off-road style driving, every 30-50,000 miles is a reasonable interval to change this part of your truck, in order to prevent a catastrophic failure. So, today I headed out to the shop to check my LBJs, and here's what I found. This time, it's been 15 months, and it's definitely time for replacement. Before you do this test, you want to jack up the…
3 Comments
Today was going to be an easy day working on the truck. I knew what I had to do and it wasn't hard. I'd gathered the parts I needed - twice really, since the first time I tried to do this work, I found that I needed some additional bits that I thought I wasn't going to be replacing. And unlike some of my more advanced projects, I had all the tools for this one already. After 27K miles on the ADS coilovers that I installed earlier this year, it was time to replace the spherical bearings. Well - the…
4 Comments
Well, the Tacoma got a new fuel filter today. It's a part I've had sitting around for maybe 18 months now or so, just taking up room in the garage. Because, who needs to install a new filter when the one that's on there seems to be working just fine. Right? Well, it finally dawned on me why they call it preventative maintenance, and I figured I might as well get it done. Interested in doing this yourself? Here is a handy little how-to that lists the tools and parts you'll need: How-to: Replace the Fuel Filter in a 96-04…
8 Comments
When it rains, it pours! It was only a few weeks ago that I replaced the rear axle seals on the 3rd gen 4Runner. No good deed goes unpunished however, and it was only a couple days after doing the job that the same failure happened on the Tacoma - only this time, I was in Canada. Luckily for me, I already had a well thought-through step-by-step list of exactly what to do, and the muscle memory of doing it once twice already. Step-by-Step: Replacing Rear Axle Seal & Bearing on a 1st gen Tacoma w/ABS (or 3rd gen 4Runner)…
1 Comment
Every now and then, there's some un-sexy, mundane, stuff that we do to our trucks just to keep them in good working order. These don't usually get a lot of publicity since they do little to increase the cool factor, and don't have the high-profile pizzazz worthy of the 'gram. So today, I did a bit of maintenance. Since getting the @RelentlessFab sliders installed a couple of years ago, they've done everything I've asked of them and have required essentially no maintenance. But, as time has passed, I've noticed that the area where they were welded to the frame has…
2 Comments
Just to set expectations - there are no amazing photos in this post. Actually, there are no photos at all - it's just a story. A story of how my day started off one way, and ended another. Come laugh at with me, and enjoy! So, today I was going to work on the 4Runner. I've been getting it into shape so that it can become our family adventure vehicle and daily driver. As such, it's getting a lot of love in the "let's make sure that key parts are in known condition" department - today's work was going to be…
Leave a Comment
People often assume that everything is easy for me. That I just go about doing things, and usually doing them well. That's sort of the case, since I've had a lot of experience doing different things in my life and I tend to pick things up quickly, but I think it's important to recognize that even for people who seem "good at everything," not everything is easy. Getting in there and trying things can still be both hard and rewarding, no matter who you are... I don't know why, but I've been super nervous about changing my spark plugs and…
1 Comment
It was just a couple days ago that I noticed my front diff was leaking. Actually, I noticed it only because I was replacing my AC idler pulley for the second time in a month - having replaced it on The De-Tour last year and recently again with less than a week of the F.U. Rain trip remaining. I sure hope this time lasts longer than a week on the trail and a few muddy water crossings! But that's not what this post is about - this post is about my front diff. While I was under the truck with the…
4 Comments
This is a long, wordy post. Sorry, and enjoy the story. As we drove the several-hundred-miles to eastern Oregon on our recent trip to Owyhee and the Alvord Playa, all was not well with the Tacoma. Four times - each time after three uninterrupted hours of driving - there would be a sudden sound of something that sounded like a bearing "spinning up." The sound was disconcerting enough that I'd immediately take my foot off the gas, and the sound would slow - eventually ending in a clunk and everything would be "back to normal." Everything that is except my…
7 Comments
If there's one thing I've learned when it comes to first gen Toyota Tacoma's, it's that the weak point of the design (well, excluding rusty frames) is the lower ball joint (LBJ) on the front suspension. The design of the joint makes it susceptible to failure, and that failure is often catastrophic if you're traveling at any kind of speed. And sometimes, even if you're not. So, over the last year as I've been pushing the truck harder, I've been keeping an eye on my LBJ's - they're the originals after all, nearly 20 years old, and with 95,000 miles…
Leave a Comment
Well, the good news is that we were successful. It may have taken 14 hours, but the Dan's (@drr and I) were triumphant in our first attempt at a timing belt self-service to each of our 5VZFE's. But oh, how we're getting ahead of ourselves. Let's back up say... six months. Just for a moment. Back in January, I was sure that I was going to have Toyota do my 90K mile service at the end of the summer, after this year's trips were in the books. I knew I'd be a little over 90K, but I figured it was…
10 Comments
It wasn't long ago that Dan (@drr), Mike (@Digiratus), Zane (@Speedytech7) and I got together at Dan's shop to do some work on Mike's steering rack and LCA's. That didn't go exactly as planned, but we all had a great time and when we hear Zane was going to be in town again, we knew right away that we should get together again - even if just to hang out. Of course, we all had a few little things we wanted to do to our trucks (isn't that always the case?) so we decided to meet up at Mike's this…
Leave a Comment
I was ready for adventure - running solo, I was returning to Death Valley, having only just wet my appetite on our first trip back in January. With 2500 miles to go, I knew I had a lot of driving ahead - but I was ready - or so I thought - when, less than 50 miles in, the Check Engine Light (CEL) came on. I've covered the details of the first hours of diagnosis in my Back to Death Valley trip report, so if you haven't read that (and are interested), I'd recommend starting there. The plan here is…
6 Comments
Our trip to The Maze was awesome. However, you may recall that near the end, we hit a whoops a little fast, which led to me peering under the truck a few times on the way home to try and determine what the god-awful shake was that we were feeling in the accelerator, seats, and - after 15 hours on the road - our bones. I wasn't able to figure it out on the drive home, but the next day I spent some more time under the truck and noticed two things: The rear diff pinion seal had started leaking…
1 Comment
With summer fast approaching, I decided that it'd be a good time to take a look at the skids - so I could clean up any rust, and repaint them for the season. I'm not sure how necessary that is - I mean, at 3/16" thick, these @relentlessfab plates would take quite a while for rust to destroy - but it's an easy process, so why not. Removal was straight forward though a bit unwieldy, and I was happy to find that my re-welded anchors were holding up well. I was also happy to see that my skids had saved…
Leave a Comment
I've never been a car guy. I can tell you all about the details of construction and woodworking - how the various bits of a house work, how to precision tune a saw or plane. But when I looked down and saw two flaking, worn bushings that were connected to "some bar" and my lower control arms, I wondered, "What the heck is that, and how screwed am I?" As it turns out, that was my stabilizer bar, and I wasn't really all that screwed at all. But I'm getting ahead of myself. See, the first thing I did was consult…
2 Comments